Drinking water hygiene

drinking water hygiene

Drinking water: our most important foodstuff

Like other foodstuffs, drinking water also has a limited shelf life. If water stagnates in the pipes, also referred to as increasing water age, it can spoil.  When stagnation occurs, drinking water absorbs substances from the installation materials as well as temperature from the environment. Both can lead to a changed drinking water quality that is harmful to human health. A temperature increase to over 25°C is particularly alarming, as microorganisms such as Legionella multiply explosively in lukewarm temperature ranges. A temperature of just <20°C is regarded as safe for cold water in many international standards and recommendations.

Therefore, especially operators of public buildings have to ensure hygienically perfect drinking water throughout the entire plumbing installation at all times. To meet this requirement, it is necessary to rule out the four main risks for a decrease of drinking water hygiene during design, installation and operation.

The four success factors that ensure perfect drinking water hygiene

Challenges in the design and implementation of drinking water hygiene

The four success factors that ensure perfect drinking water hygiene

1. Flow

Trinkwasserhygiene Durchströmung Piktogramm

The pipes must be sized that occurring velocities generate shearing forces on the pipe walls during daily periods of high water consumption. The shearing forces minimize the build up of biofilm as adherence of particles is avoided.

Structural design influences piping network parameters that are relevant to hygiene

The structural design of a drinking water installation has a considerable influence on the piping network parameters that are relevant to hygiene such as wetted pipe surface and installation volume. To prevent stagnation and reduce water age in the pipes, the piping network must be designed with the objective to achieve as short as possible pipe connections to the tap. An example to minimize and equalize the length of pipe connections is a centralized incoming main supply into the plumbing installation.

Objective: short flow paths and minimal pipe volume

Trinkwasserhygiene-Ziel zur optimalen Durchströmung: kurze Fließwege und geringer Rohrleitungsinhalt

Short flow paths to the taps lead to a greater available pressure gradient in a piping network calculation. As a result, small pipe diameters can be selected. This means that higher flow velocities are achieved in all sections of the main distribution line when the drinking water installation is in use and therefore higher shearing forces come into effect on the pipe walls. Lower pipe contents with the same frequency of use at the taps also leads to a reduction of water age in the supply system. The exchange of water is therefore intensified and thus the average temperature level is significantly decreased. Comparative calculations show that the water content of a piping network can differ by up to 30% depending on the type of distribution concept.

Different distribution concepts

There are generally two different distribution concepts available for supplying drinking water to a building:

Horizontal distribution

In a horizontal distribution system, a main riser supplies water to a horizontal supply pipe in each floor of a building. The horizontal supply pipe of a floor is usually installed in the void of the corridor. All e.g. bathrooms are connected to this pipe to then supply the taps. Predominantly horizontal distribution systems are often found in buildings with large numbers of installations such as hospitals and hotels.

Horizontale Verteilung bei hochinstallierten Gebäuden

Horizontal distribution

In a horizontal distribution system, a main riser supplies water to a horizontal supply pipe in each floor of a building. The horizontal supply pipe of a floor is usually installed in the void of the corridor. All e.g. bathrooms are connected to this pipe to then supply the taps. Predominantly horizontal distribution systems are often found in buildings with large numbers of installations such as hospitals and hotels.

Vertikale Verteilung z. B. bei Wohngebäuden

2. Temperature

Trinkwasserhygiene Temperatur Piktogramm

In circulating hot water systems, the water temperature must be kept above 55°C everywhere, in the Netherlands for example, even above 60°C. The water content of a hot water installation, which cannot be held at this temperature must be minimised. The cold water temperature should be less than 25°C, and should preferably not exceed 20°C. If these temperatures cannot be maintained, this can lead to a change in drinking water quality that can be harmful to human health. A temperature increase to over 25°C is particularly alarming, as microorganisms such as Legionella multiply explosively in lukewarm temperature ranges. Therefore, especially operators of public buildings have to ensure hygienically perfect drinking water throughout the entire installation at all times.

Influence of internal heat loads

Einfluss innerer Wärmelasten

Heat sources such as hot water pipes of plumbing and heating systems and components of electrical and ventilation systems lead to a temperature increase of the cold drinking water pipes above 25°C within two hours of stagnation, even if the insulation is according to standards.

Influence of external head loads

Einfluss äußerer Wärmelasten

High ambient air temperatures

High outside air temperatures can cause ambient air temperatures of more than 25°C in buildings without air conditioning. In the event of stagnation, cold water temperatures below 25°C can no longer be achieved as a result.

Water inlet temperatures

Where drinking water is sourced near ground level in the summer months, the temperature of water coming into drinking water installations is higher (>20°C), reducing the maximum tolerable stagnation time even more.


3. Water exchange

Trinkwasserhygiene Wasseraustausch Piktogramm

The design of a drinking water installation must result in a frequent water exchange in all parts of the building, particularly in the floor- and single supply pipes.

Microbial contamination through stagnation

Hygiene experts are constantly detecting inadequate drinking water hygiene in drinking water installations. The problems are present in both cold and hot water. Among experts, the primary cause of microbial contamination and therefore the change from drinking water to non-drinking water is said to be stagnation. The cause of stagnation areas can be old, unused pipes or sections of pipe which are temporarily not being used. These areas are therefore potentially a source of error in the drinking water installation.

Operators under obligation

Trinkwasserhygiene: Betreiber in der Pflicht

The responsibility for the frequent exchange of water lies solely with the operator. It is recommended to separate unused pipes from the drinking water installation or to use all sections of the pipeline as intended. 'As intended' means that an adequate frequency of use and a frequent water consumption respectively has to be taken as the basis.

Change of usage behaviour

In many cases, the use of a building or usage behaviour has changed over a certain period of time. If the planned consumption of drinking water does not occur in sections of the piping installation as intended, the operation of the entire drinking water installation can be paralysed by germs. The originally planned operation as intended can then only be maintained by flushing measures.

Manual flushing measures

Trinkwasserhygiene: Personalintensiver manueller Wasserwechsel

Manual flushing measures by opening and closing all taps affected means an increase of operating cost of the building. The additional operating and staff costs incurred as a result are seldom recognised and taken into account during the design phase. The consistent compliance with these flushing measures is as questionable as the objective being striven for, i.e. achieving the exchange of the entire water content. If just the measures on the flushing schedule already cause disproportionately high costs, then it can become extremely expensive if the manual implementation is not carried out carefully over time and hygiene deficiencies are detected when samples of the drinking water are tested.


4. Nutrient supply

Trinkwasserhygiene Nährstoffangebot

The release of nutrients from materials must be reduced as far as technically possible. This also indirectly serves to prevent microbial growth both on the surface of the material and in drinking water.

Migration of material components encourages biofilm development

Verkeimung durch Biofilm

Longer contact between drinking water and materials (e.g. piping and valve) can cause parts of the materials to migrate into the drinking water, resulting in the concentration of nutrients. A combination of poor material quality, stagnation and unfavourable water quality encourages the strong development of biofilm, under the protection of which facultative pathogens can also multiply.

Reduction in the release of nutrients from materials

Complex components such as valves pose particular problems here. The microbiome controls a whole host of growth stimulating factors during stagnation phases. Since water is not removed in stagnation phases, the planktonic microorganisms that have made their way into the water are not diluted. The migration of nutrients from materials in contact with drinking water must therefore be reduced to the technically possible minimum. All materials must be tested for their suitability for drinking water usage.


KHS-Logo

KHS hygiene system

The KEMPER Hygiene System, KHS, prevents stagnation and the resultant impairment of drinking water quality. It ensures that fresh, hygienically perfect water is always available at every tap, taking into consideration efficiency and sustainability concerns. It offers every stakeholder, from the planner to the operator, from the installer to the end consumer, maximum security and safety in their daily contact with drinking water.

KHS-Venturi flow splitter

KHS-Venturi flow splitter

KHS Control Systems

KHS Control Systems

KHS Floor Box

KHS Floor Box

HS2 Hygiene Flushing Box

KHS HS2 Hygiene Flushing Box

KHS Valves for water changing

KHS Valves for water changing